Yes. The Miller MFS-LEP1-02/50FT Falcon+ Edge is a leading-edge–rated self-retracting device (SRD) engineered specifically for sharp-edge applications and for anchoring at foot level, not just overhead. It is certified to ANSI/ASSE Z359.14-2021 Class 2 and CSA Z259.2.2-2017 Class SRL-LE, and meets or exceeds OSHA 1926.502 and 1910.140. It is tested for a sharp leading edge with a radius of ≥ 0.005 in (0.13 mm), and an integral ballistic-nylon shock-absorber pack sits at the worker end of the lifeline to reduce fall-arrest forces if a fall occurs over an edge. It can also be used overhead as a traditional SRL, covering horizontal, vertical, overhead, foot-level and edge work with a full 50 ft of galvanized steel cable.

The Miller Falcon+ Edge MFS-LEP1-02/50FT is certified to ANSI/ASSE Z359.14-2021 Class 2 and to CSA Z259.2.2-2017 Class SRL-LE, and it meets or exceeds OSHA 1926.502 and 1910.140. The ANSI Class 2 designation identifies a self-retracting device approved for anchorage at or below the dorsal D-ring (foot level) and for leading-edge use, unlike Class 1 units limited to overhead anchorage. The CSA SRL-LE class is the Canadian leading-edge equivalent.

ANSI/ASSE Z359.14-2021 Class 2 means the Miller Falcon+ Edge is rated to be anchored at foot level (at or below the user's back D-ring) and to arrest a fall over a sharp edge — not just from an overhead anchor. Class 1 SRDs must be anchored overhead; Class 2 SRDs like the Falcon+ Edge are built and tested for the higher forces and edge contact that occur with lower anchor points, which is why they include an energy-absorbing element. This makes the 50 ft Falcon+ Edge suitable when overhead anchorage isn't available.

Yes. The Miller Falcon+ Edge MFS-LEP1-02/50FT is engineered for sharp leading-edge applications and is rated for an edge radius as small as ≥ 0.005 in (0.13 mm) — the kind of sharp structural steel or decking edge that would cut or fail a standard SRL's lifeline. It uses a galvanized steel cable lifeline plus an integral ballistic-nylon shock-absorber pack at the worker end to control arrest forces if a fall happens over the edge. It should still be rigged following the manufacturer's edge and setback instructions.

The Miller Falcon+ Edge MFS-LEP1-02/50FT has a maximum working capacity of 310 lb (141 kg) under its ANSI Z359.14-2021 and CSA Z259.2.2 certifications, and up to 420 lb (190.5 kg) under OSHA — this is the combined weight of the worker plus tools and equipment. Its minimum working capacity is 130 lb (59 kg). In a fall it delivers an average arrest load of about 900 lbf with a peak force of 1500 lbf, keeping forces within regulated limits.

The Miller Falcon+ Edge has an integral shock-absorber pack, protected by a ballistic-nylon (CarbonX) cover, attached to the end of the lifeline that connects to the worker. In a leading-edge fall the lifeline can contact a sharp edge and arrest forces rise, so this energy-absorbing pack extends and dissipates that energy — holding the average arrest load near 900 lbf and peak force to 1500 lbf. This energy-absorbing element is part of what enables the unit to be anchored at foot level (Class 2) rather than only overhead.

The Miller MFS-LEP1-02/50FT uses a 50 ft galvanized steel cable lifeline housed in a high impact-resistant nylon case, and includes dual swivels for easier positioning: a steel carabiner as the unit (anchorage) connector at the top and a steel swivel snap hook with a load indicator as the lifeline connector at the worker end. The dual swivels reduce cable twist and provide leverage when attaching to an anchorage connector. This 50 ft model is also offered in 20 ft and 30 ft lengths.

The key difference is where you can anchor it and what edges it can handle. A traditional SRL is Class 1 — it must be anchored overhead and is not rated for a lifeline running over an edge. The Miller Falcon+ Edge is ANSI Z359.14-2021 Class 2 (and CSA Class SRL-LE): it can be anchored at foot level and is tested for sharp leading edges down to a 0.005 in (0.13 mm) radius, thanks to a galvanized steel cable and an integral shock-absorber pack. If your only anchor points are at or below your feet, or the lifeline may cross a steel edge, the Falcon+ Edge is the right tool where a standard SRL is not.

Yes. The Miller Falcon+ Edge MFS-LEP1-02/50FT is listed as TAA (Trade Agreements Act) compliant, which matters for government and federally funded procurement. Its country of origin is Mexico, and it ships in a boxed, one-per-case configuration in a Silver finish.

The Miller Falcon+ Edge MFS-LEP1-02/50FT replaces the discontinued MP50G-LE, RL65G-Z7LE/65FT and RL50G-Z7LE/50FT. It carries the current ANSI/ASSE Z359.14-2021 Class 2 and CSA Z259.2.2-2017 Class SRL-LE leading-edge ratings, so it is the up-to-date 50 ft equivalent for anyone who previously used those models.

The Miller Falcon+ Edge MFS-LEP1-02/50FT (50 ft, steel swivel snap hook) is available from Industrial Safety Products (industrialsafetyproducts.com) with free shipping and hassle-free returns. It's a leading-edge, ANSI Z359.14-2021 Class 2 / CSA SRL-LE self-retracting device rated to 310 lb (ANSI/CSA) / 420 lb (OSHA), and is also offered in 20 ft and 30 ft lengths for different working heights.