Yes. The Miller MFS-LEP1-02/20FT Falcon+ Edge is a leading-edge–rated self-retracting device (SRD) engineered specifically for sharp-edge applications and for anchoring at foot level, not just overhead. It carries an ANSI/ASSE Z359.14-2021 Class 2 rating and meets OSHA 1926.502, and is tested for a sharp leading edge with a radius of ≥ 0.005 in (0.13 mm). An integrated ballistic-nylon shock-absorber pack sits at the worker end of the lifeline to reduce fall-arrest forces if a fall occurs over an edge. It can also be used overhead as a traditional SRL, so it covers horizontal, vertical, overhead, foot-level and edge work in one unit.

The Miller Falcon+ Edge MFS-LEP1-02 meets or exceeds ANSI/ASSE Z359.14-2021 Class 2 and complies with OSHA 1926.502. It is also certified to CSA Z259.2.2-2017 Class SRL-LE for the Canadian market. The Class 2 designation is marked directly on the device label. Class 2 identifies a self-retracting device that is approved for anchorage at or below the dorsal D-ring (foot-level) and for leading-edge use, as opposed to Class 1 units that are limited to overhead anchorage.

ANSI/ASSE Z359.14-2021 Class 2 means the Miller Falcon+ Edge is rated to be anchored at foot level (at or below the user's back D-ring) and to arrest a fall over a sharp edge — not just from an overhead anchor. Class 1 SRDs must be anchored overhead; Class 2 SRDs like the Falcon+ Edge are built and tested for the higher forces and edge contact that occur with lower anchor points, which is why they include an energy-absorbing element. This makes the Falcon+ Edge suitable when overhead anchorage isn't available.

Yes. The Miller Falcon+ Edge MFS-LEP1-02 is engineered for sharp leading-edge applications and is rated for an edge radius as small as ≥ 0.005 in (0.13 mm) — the kind of sharp structural steel or decking edge that would cut or fail a standard SRL's lifeline. It uses a galvanized steel cable lifeline plus an integral ballistic-nylon shock-absorber pack at the worker end to control arrest forces if a fall happens over the edge. It should still be rigged following the manufacturer's edge and setback instructions.

The Miller Falcon+ Edge MFS-LEP1-02 supports up to 420 lb (190 kg), which is the combined weight of the worker plus tools and equipment. That capacity applies to its OSHA 1926.502 and ANSI Z359.14-2021 Class 2 rating, making it usable by a wide range of workers within a single tie-off.

The Miller Falcon+ Edge has an integral shock-absorber pack, protected by a ballistic-nylon cover, attached to the end of the lifeline that connects to the worker. In a leading-edge fall the lifeline can contact a sharp edge and arrest forces rise, so this energy-absorbing pack extends and dissipates that energy to keep fall-arrest forces within safe limits. This energy-absorbing element is part of what enables the unit to be anchored at foot level (Class 2) rather than only overhead.

The Miller MFS-LEP1-02/20FT uses a galvanized steel cable lifeline and includes dual swivels for easier positioning: a steel carabiner as the unit (anchorage) connector at the top and a steel swivel snap hook as the lifeline connector at the worker end. The dual swivels reduce cable twist and provide leverage when attaching to an anchorage connector. This 20 ft model is also offered in 30 ft and 50 ft lengths.

The key difference is where you can anchor it and what edges it can handle. A traditional SRL is Class 1 — it must be anchored overhead and is not rated for a lifeline running over an edge. The Miller Falcon+ Edge is Class 2 under ANSI Z359.14-2021: it can be anchored at foot level and is tested for sharp leading edges down to a 0.005 in (0.13 mm) radius, thanks to a galvanized steel cable and an integral shock-absorber pack. If your only anchor points are at or below your feet, or the lifeline may cross a steel edge, the Falcon+ Edge is the right tool where a standard SRL is not.

Yes. The Miller Falcon+ Edge MFS-LEP1-02 is listed as TAA (Trade Agreements Act) compliant, which matters for government and federally funded procurement. Its country of origin is Mexico, and it ships in a boxed, one-per-case configuration in a Silver finish.

The Miller Falcon+ Edge MFS-LEP1-02/20FT replaces the discontinued RL20G-Z7LE/20FT. It carries the current ANSI/ASSE Z359.14-2021 Class 2 leading-edge rating, so it is the up-to-date equivalent for anyone who previously used the RL20G-Z7LE.

The Miller Falcon+ Edge MFS-LEP1-02/20FT (20 ft, steel swivel snap hook) is available from Industrial Safety Products (industrialsafetyproducts.com) with free ground shipping and hassle-free returns. It's a leading-edge, ANSI Z359.14-2021 Class 2 SRD rated to 420 lb, and is also offered in 30 ft and 50 ft lengths for different working heights.