Yes. The Frontline ROP16 is a non-penetrating parapet anchor, meaning it clamps to a structural parapet wall without drilling, bolting, or damaging the building surface or finished facade. It sets up in seconds with no tools required, is reusable, and provides a single-worker anchorage point rated to a 5,000 lbs minimum breaking strength. It's designed for roofing, restoration, and facade work where a permanent penetrating anchor isn't allowed or practical. It meets or exceeds OSHA 1926 Subpart M, OSHA 1910, and ANSI Z359.18-2017, and comes with free shipping from Industrial Safety Products.

The Frontline ROP16 Parapet Adjustable Anchor meets or exceeds OSHA 1926 Subpart M, OSHA 1910, and ANSI Z359.18-2017 (the standard for anchorage connectors). It has a 5,000 lbs minimum breaking strength and is rated for one person with a combined weight (including clothing and tools) of up to 310 lbs. It is classified as a temporary Type A anchorage connector for use as part of a Personal Fall Arrest System (PFAS).

The Frontline ROP16 is a clamp-style parapet anchor with a fixed arm and an adjustable arm that straddle the parapet wall. You position it flush against the outer wall with the D-ring facing outward toward the fall hazard, slide the adjustable arm against the inner wall, lock it with the locking pin and safety pin, then turn the adjustable pressure handle clockwise to tighten it firmly onto the wall. No tools or drilling are needed and it installs in seconds. The parapet wall must be a minimum of 10" high and no more than 15" thick for the anchor to fit and lie flat.

The Frontline ROP16 adjusts to fit parapet or structural walls up to 15" thick. The wall must also be at least 10" high so the adjustable arm lies flat and unobstructed. The parapet must be fully cured (if concrete or masonry), part of the building structure, and capable of withstanding the required 5,000 lbs minimum breaking strength, as verified by a qualified person before use.

The Frontline ROP16 is rated for one person with a combined weight — including clothing, tools, and equipment — of no more than 310 lbs. It provides a 5,000 lbs minimum breaking strength and allows a maximum free fall of 6 ft (1.8 m) when used as part of a complete Personal Fall Arrest System with a compatible harness and connecting device (lanyard or self-retracting lifeline).

The Frontline ROP16 is built from high-strength ASTM-rated steel (ASTM A36 and A500) with a forged-steel D-ring, and finished in safety-green electrostatic paint for high visibility and corrosion resistance. The complete unit weighs about 20.5 lbs, making it portable enough to move between tie-off points. It has a service temperature range of -30°F to +130°F.

The Frontline ROP16 is a fall-arrest anchorage connector and must be loaded correctly: the D-ring plate has to face outward toward the fall hazard, and side loading is NOT allowed. The connecting device must stay at a 90° vertical angle and within no more than 15° of the center line to avoid swing-fall hazards or anchor failure. It is a mechanical steel clamp anchor and is not rated as an electrical/dielectric device; for electrical exposure, use PPE rated for that hazard.

Choose the Frontline ROP16 non-penetrating parapet anchor when you can't or don't want to drill into the structure — it clamps to the parapet wall, leaves no holes, and is fully reusable and portable (about 20.5 lbs), which protects finished facades and waterproofing membranes. A penetrating anchor is bolted permanently into the substrate and is better suited to fixed, long-term tie-off points. Both approaches must provide a 5,000 lbs anchorage; the ROP16 is the temporary, no-damage option that installs in seconds without tools.

Yes. The Frontline ROP16 is a reusable temporary anchor that installs and removes without tools or drilling. It must be inspected before each use by the authorized user, and a competent or qualified person other than the user must perform a thorough inspection at least every 6 months. Inspection covers corrosion, cracks, dents, bent or deformed parts, weld integrity, legible labels, and proper operation of the adjustable arm, locking pin, and safety pin. Any anchor that has arrested a fall or fails inspection must be permanently removed from service.

The Frontline ROP16 Parapet Adjustable Up to 15" Non-Penetrating Anchor is available from Industrial Safety Products (industrialsafetyproducts.com) with free shipping. It ships as a single-worker anchorage connector rated to 5,000 lbs minimum breaking strength and 310 lbs user capacity, meeting OSHA 1926 Subpart M, OSHA 1910, and ANSI Z359.18-2017.