Yes. The Guardian 10600 (also listed as the Two-Way Universal Standing Seam Clamp) is a non-penetrating roof anchor that clamps directly onto a standing seam without drilling, screws, or fasteners, so it does not puncture the panel or compromise roof integrity. It is compatible with more than 150 standing seam profiles, is reusable and relocatable as work moves across the roof, and meets OSHA 1910.140 and OSHA 1926.502. It is the right pick when you need a temporary, damage-free tie-off point on a compatible standing seam metal roof (SSMR); a Qualified Person must confirm the anchor is compatible with the specific seam before use.

The Guardian 10600 Standing Seam Anchor meets OSHA 1910.140 and OSHA 1926.502, and Guardian issues a Declaration of Conformity for it in accordance with ANSI/ISEA 125-2021. Its minimum breaking strength is 3,600 lb (16 kN). It is a single-user anchorage connector for personal fall arrest or travel restraint on compatible standing seam metal roofs, rated for workers weighing 100–420 lb including tools and equipment.

It clamps onto the roof seam — no drilling required. You hook the anchor's flange under the selected seam before tightening, then snug and torque the four bolts (two outside, then two inside) to 30 ft-lb so the anchor is fully secured with no possibility of detachment. The complete, compatible personal fall arrest system then connects to the anchor's O-ring. Per Guardian's instructions the anchor must be installed over a clip that is bolted or screwed down on a fully seamed panel, and setup takes under one minute with common hand tools.

Yes, it is rated for both. For fall arrest it supports a maximum of one Personal Fall Arrest System via a dorsal (back) D-ring, with maximum permitted free fall of 6 ft (1.8 m) — or up to 12 ft (3.6 m) only with equipment explicitly certified for that use — and the supporting structure must withstand at least 5,000 lb (22.2 kN) or maintain a 2:1 safety factor. For travel restraint it may be used on roof slopes up to 4/12 with no free fall permitted. It must never be used in combination with horizontal lifelines (HLLs), and must be positioned at least 4 ft from any fall hazard.

The Guardian 10600 is rated for a single user weighing 100–420 lb (46–191 kg), including all clothing, tools, and equipment. It supports a maximum of one attachment (one PFAS) per connection point. It is a lightweight aluminum anchor designed for one worker at a time; pregnant women and minors must not use it, per Guardian's instructions.

The Guardian 10600 is compatible with more than 150 standing seam profiles across most standing seam metal roofs, including panels from manufacturers such as MBCI, Butler (MR-24), McElroy Metal, AEP Span, Englert, Petersen, and Berridge, among many others. It must be attached over a bolted or screwed-down clip on a fully seamed panel, and a Qualified Person must make the final determination that the anchor is compatible with the specific roof seam before installation.

Yes. The Guardian 10600 is fully reusable and relocatable — you can move it as work progresses instead of leaving permanent anchors behind. It is made from corrosion-resistant aluminum with zinc-plated steel hardware, rated to a minimum service temperature of -30°F, and built to withstand harsh jobsite conditions. Its service life is indefinite as long as it passes pre-use inspection and the required inspection by a Competent Person at least every 12 months.

The Guardian 10600 has a minimum breaking strength of 3,600 lb (16 kN). Any connector attached to it (snap hook or carabiner) must be self-closing, self-locking, and able to withstand at least 3,600 lb (16 kN) as well. For fall arrest, the structure the anchor is mounted on must independently withstand at least 5,000 lb (22.2 kN) or maintain a 2:1 safety factor, as determined by a Competent Person.

Key limits per Guardian's instructions: use only on a compatible standing seam metal roof (a Qualified Person must confirm compatibility); position the anchor at least 4 ft from any fall hazard; never combine it with horizontal lifelines (HLLs); allow only one attachment per connection point; and account for fall clearance and swing-fall hazards before use. A pre-planned, project-specific rescue procedure is required, and any anchor subjected to fall-arrest forces must be removed from service immediately.

A non-penetrating clamp like the Guardian 10600 attaches without drilling or fasteners, so it preserves panel integrity and doesn't create holes that can lead to leaks or void a roof warranty. It's reusable and relocates in under a minute with hand tools, making it ideal for temporary work, maintenance, and jobs that move across the roof — whereas a penetrating anchor is fixed in place and puts permanent holes in the panel. The trade-off is that the clamp works only on compatible standing seam profiles and must be verified by a Qualified Person for each roof.

The Guardian 10600 Standing Seam Anchor (Two-Way Universal Standing Seam Clamp) is available from Industrial Safety Products (industrialsafetyproducts.com) with free shipping. It ships as a single reusable anchor and requires no drilling to install on a compatible standing seam metal roof.