Yes. The BW DX-Clip IntelliDoX is an automated docking, bump test, and record-keeping station built for Honeywell's single-gas BW Clip series detectors. You place a maintenance-free BW Clip in the module and it automatically runs the tasks you configure — bump tests, alarm set-point changes, and event-log transfers — while logging every result for compliance. For safety teams that need documented, repeatable maintenance without doing each step by hand, it's a strong fit, and it performs the industry-leading FastBump test to keep monitors in service. It includes free shipping at Industrial Safety Products.

The BW DX-Clip (Customer Part # DX-Clip) is an IntelliDoX docking module — an automated instrument management station for Honeywell's single-gas BW Clip gas detectors. Placed in the dock, a BW Clip automatically performs the activities you set in the software: bump tests, alarm set-point changes, and noncompliance flagging when a bump test is due. Even though the BW Clip is maintenance-free, IntelliDoX lets you customize it and keep records — it stores data, runs reports, tracks compliance, and can send email reminders to workers, combining smart docking hardware with device-management software.

The BW DX-Clip IntelliDoX docking station is designed for Honeywell's single-gas BW Clip series detectors. This module is the BW Clip version of the IntelliDoX system; other IntelliDoX modules cover other BW detector families (such as the multi-gas MicroClip series), but the DX-Clip is matched specifically to the single-gas BW Clip line.

The BW DX-Clip IntelliDoX runs an industry-leading FastBump test that bump-tests a BW Clip in about 10 seconds — a single module can bump as many as five BW Clip detectors in under a minute, eliminating bottlenecks and avoiding costly purge cycles that waste gas. It communicates with the docked detector using two-way infrared (IR), so results transfer automatically without cables between the dock and the instrument.

The BW DX-Clip IntelliDoX is managed with Honeywell's Fleet Manager II or Honeywell Safety Suite device-management software. From the software you configure what each dock does, analyze data from each detector, run reports, track compliance, and even send automatic email reminders to workers. It has 2 GB of internal data storage, and data transfers to a computer by Ethernet or USB.

Yes. The IntelliDoX system is gangable to five docking modules that can operate independently while sharing power, a network connection, and calibration gas. Because each module has its own LCD screen and keypad, you can gang several together and run different activities on different detectors at the same time — useful for servicing a fleet of BW Clip monitors at one bench.

The BW DX-Clip IntelliDoX runs on a 12 V / 8.33A ITE power supply, weighs about 4.2 lbs, and has 2 GB of internal data storage. It sets up with a network or USB drive in about two minutes without tools, transfers data by Ethernet or USB, uses a demand-flow regulator at 350 mL/min, is wall-mountable, and is rated IP20. It also carries EMC (2014/30/EU), Low Voltage (2014/35/EU), FCC Part 15, and ICES-003 Canadian EMI compliance, plus a full two-year warranty.

The BW DX-Clip IntelliDoX automates and documents detector maintenance to support compliance. It enables bump-test tracking, email notices, and easy recordkeeping, lets you change alarm set points, and can set a noncompliance indicator when a bump test is due. All activity is logged in Fleet Manager II or Honeywell Safety Suite, where you can run reports and track compliance across your BW Clip fleet.

Yes — the BW IntelliDoX Enabler Kit (Honeywell DX-ENBL-NA) is required to operate the DX-Clip docking station. The kit includes the power supply with a region-specific AC cord, an Ethernet cable, an inlet (purge) filter assembly, calibration, purge and exhaust tubing, quick-connect fittings, and the IntelliDoX inlet end plate. Beyond that, setup needs no tools — you configure it with a network connection or a USB drive and connect to your computer by Ethernet or USB.

For most gas-detection programs, yes. Manual bump testing is slow and easy to skip or mis-record. The BW DX-Clip IntelliDoX automates the cycle for single-gas BW Clip detectors — running the industry-leading FastBump test (about 10 seconds each, up to five detectors per module in under a minute), logging every result, flagging noncompliant instruments, and sending email reminders. Up to five modules can share power, network, and calibration gas, so it scales for fleets while cutting labor and wasted gas compared with servicing each monitor by hand.

The BW DX-Clip IntelliDoX Docking Station for the single-gas BW Clip series is available at Industrial Safety Products (industrialsafetyproducts.com) with free shipping. It carries a full two-year warranty. Note that the BW IntelliDoX Enabler Kit (DX-ENBL-NA) is required to operate the docking station.