Yes. The Miller MTL-LEP2-62/9FT Turbolite+ Edge is a twin (dual-leg) leading-edge self-retracting device that gives you 100% tie-off: because it has two independent lifelines, you can always keep at least one leg anchored while you move between anchor points, never being unprotected. It is rated ANSI Z359.14-2021 Class 2 and meets OSHA 1926.502 and 1910.140, so it can be anchored at foot level (not just overhead) and is engineered for leading-edge applications. With a galvanized steel cable lifeline, steel locking rebar hooks and an aluminum one-pin harness connector, it's built for demanding construction, steel-erection and utility work where you're climbing or repositioning at height.

The Miller Turbolite+ Edge Twin MTL-LEP2-62 meets or exceeds OSHA 1926.502 and 1910.140 and is certified to ANSI Z359.14-2021 Class 2. Class 2 identifies a self-retracting device approved for anchorage at or below the dorsal (back) D-ring — foot-level tie-off — and for leading-edge use. Note that Miller lists CSA Class SRL-LE certification only for the 6 ft version of this device; this 9 ft model is rated to the OSHA and ANSI Z359.14-2021 Class 2 standards above.

ANSI Z359.14-2021 Class 2 means the Miller Turbolite+ Edge is rated to be anchored at foot level (at or below the worker's back D-ring) and to arrest a fall over a sharp leading edge — not only from an overhead anchor. Class 1 SRLs must be anchored overhead; Class 2 units like the Turbolite+ Edge are built and tested for the higher forces and edge contact that occur with lower anchor points. That is why it uses a galvanized steel cable lifeline and an energy-limiting braking design, allowing a maximum arrest distance of 24 in (0.6 m) when tested to ANSI Z359.14.

The Miller MTL-LEP2-62 is a "twin" self-retracting lifeline because it has two separate retracting legs that connect to a single point on your harness. This enables 100% tie-off: when you need to move past an obstruction or relocate to a new anchor, you connect the second leg before disconnecting the first, so you are continuously protected and never off-anchor. Twin SRLs are the standard solution for climbing steel, moving along a structure, or any task where a single lifeline would force a moment of disconnection.

The Miller Turbolite+ Edge Twin MTL-LEP2-62 supports a maximum working capacity of 310 lb (140 kg) under ANSI Z359.14-2021 and up to 420 lb (190.5 kg) per OSHA, with a minimum working capacity of 130 lb (59 kg). These figures include the worker plus tools and equipment. Its maximum peak arresting force is 900 lb (4 kN) for a 310 lb user and 1,800 lb (8 kN) for users up to 420 lb, and the device has an ultimate strength of 3,000 lb (13.34 kN).

The Miller MTL-LEP2-62/9FT uses galvanized steel cable lifelines and pairs an aluminum one-pin connector at the harness end with steel locking rebar hooks at the anchorage end. The large steel locking rebar (scaffold) hooks let you clip directly onto rebar, scaffolding tubes and other large-diameter structural members that a standard snap hook won't fit, while an integral swivel design keeps the lifelines from twisting as you move. This model has a 9 ft working length; a 6 ft version is also offered.

Yes. The Miller MTL-LEP2-62 is a leading-edge (SRL-LE) rated device, ANSI Z359.14-2021 Class 2, and can be connected both at foot level and above the worker's D-ring, supporting workers up to 420 lb (190.5 kg) per OSHA. Its galvanized steel cable and quick-activating stainless steel braking system are designed to arrest a fall even when the lifeline runs over an edge and the anchor point is below you — a scenario that overhead-only (Class 1) SRLs are not rated for. Always rig it following Miller's edge and setback instructions.

The Miller Turbolite+ Edge uses a quick-activating, high-strength stainless steel braking system: the lifeline pays out and retracts freely during normal movement, but a sudden acceleration (a fall) locks the mechanism almost instantly to arrest you within a 24 in (0.6 m) maximum arrest distance under ANSI Z359.14. It also has a visual load indicator that changes appearance once the device has arrested a fall or been shock-loaded, signaling that the unit must be removed from service. The housing is high-impact Nylene nylon with an aluminum hub for durability at low weight.

Two things set it apart: dual legs and where you can anchor it. A traditional SRL is usually a single-leg, Class 1 device that must be anchored overhead and isn't rated for a lifeline running over an edge. The Miller MTL-LEP2-62 is a twin, ANSI Z359.14-2021 Class 2 leading-edge unit: the two legs give you continuous 100% tie-off while repositioning, and Class 2 lets you anchor at foot level and take a fall over a sharp edge on a galvanized steel cable. If you climb or move along a structure, or your only anchors are at or below your feet, it does what a single overhead SRL cannot.

Yes. The Miller MTL-LEP2-62 Turbolite+ Edge Twin SRL is listed as TAA (Trade Agreements Act) compliant, which matters for government and federally funded procurement. Its country of origin is Mexico, it comes in a Silver finish, and it ships boxed one per case.

The Miller MTL-LEP2-62/9FT Turbolite+ Edge Twin SRL with steel locking rebar hooks (9 ft) is available from Industrial Safety Products (industrialsafetyproducts.com) with free shipping. It's a twin, leading-edge, ANSI Z359.14-2021 Class 2 self-retracting lifeline rated to 420 lb (OSHA) that provides 100% tie-off, and it is also offered in a 6 ft working length for shorter fall clearances.