Yes. The Frontline RW18 is a weld-on commercial anchor designed for fall arrest, fall restraint, work positioning, and rescue operations, made to be permanently welded onto structural steel members. It has a minimum breaking strength of 5,000-lbf/22 kN and its hot-dip galvanized ASTM-rated steel construction lets it stay in service indoors or outdoors through tough weather. It meets or exceeds ANSI Z359.18, ANSI A10.32, OSHA 1926, and OSHA 1910, making it a strong choice for a fixed, single-point anchor on steel structures.

The Frontline RW18 Weld-on Commercial Roof Anchor meets or exceeds ANSI Z359.18, ANSI A10.32, OSHA 1926, and OSHA 1910. It has been tested by an independent third-party lab accredited to ISO/IEC Standard 17025. Its minimum breaking strength is 5,000-lbf/22 kN, consistent with OSHA's requirement that an anchorage support at least 5,000 lbs per attached worker (or twice the intended load per OSHA 1910.140).

The Frontline RW18 is a weld-on anchor: it is permanently welded onto structural steel members using a 5/16" field weld. Welding must be performed by a certified welder. The attachment point must be structurally capable of supporting 5,000 lbs, or 2 times the intended fall-protection load, per OSHA 1910.140(13). Because it is hot-dip galvanized, it can be installed for indoor or outdoor use in all weather conditions.

Both the RW18 and RW12 are Frontline Weld-on Commercial Anchors with identical construction — ASTM-rated steel, hot-dip galvanized finish, a 3.5" diameter tube, a 0.625" U-rod, a 5,000-lbf/22 kN tensile strength, and the same ANSI Z359.18 / A10.32 and OSHA 1926/1910 ratings. The only difference is height: the RW18 stands 18" tall (weighing about 10.6 lbs), while the RW12 is the shorter 12" version. Choose the 18" RW18 when you need extra standoff height above the mounting surface.

Yes. The Frontline RW18 Commercial Anchor is compatible with an extensive range of connecting devices, including self-retracting lifelines (SRLs), shock-absorbing lanyards, and vertical and horizontal lifelines. It serves as a permanent tie-off point for fall arrest, fall restraint, work positioning, or rescue, so you can pair it with the connecting device best suited to your job.

The Frontline RW18 is made of ASTM-rated steel with an ASTM-rated hot-dip galvanized finish. The galvanizing makes it corrosion-resistant and suitable for both indoor and outdoor use, standing up to the toughest jobsites and all weather conditions. Its high-strength steel construction gives it a 5,000-lbf/22 kN minimum breaking strength.

The Frontline RW18 has an anchor height of 18" and weighs approximately 10.6 lbs. It is built around a 3.5"-diameter tube with a 0.625" U-rod cross-section. This standoff height raises the tie-off connection point above the mounting surface once the anchor is welded to a structural steel member.

Yes. The Frontline RW18 Commercial Roof Anchor has been tested by an independent third-party lab accredited to ISO/IEC Standard 17025, and it meets or exceeds ANSI Z359.18, ANSI A10.32, OSHA 1926, and OSHA 1910. It carries a minimum breaking strength of 5,000-lbf/22 kN. Independent, accredited testing helps verify that the anchor performs to its rated strength.

The Frontline RW18 Weld-on 18" Commercial Roof Anchor is available from Industrial Safety Products (industrialsafetyproducts.com) with free shipping. If a standard configuration doesn't fit your structure, Frontline also offers custom anchors on request, so you can specify a weld-on anchor suited to your specific application.

The Frontline RW18 is a permanent anchor. It is welded directly onto structural steel members with a 5/16" field weld by a certified welder, so it is not a temporary or reusable-clamp anchor. This makes it well suited for fixed tie-off points on steel roofs and structures where a durable, always-available anchorage is needed for fall arrest, restraint, positioning, or rescue.